Adhesive for repairing sieves and filter belts ATK PU9

Glue - a sealing compound for the production and repair of screens, filter belts and filters. The ATK PU9 version is a basic product for the following applications in a 50 ml package in a set with a squeezer and 3 agitators. The choice of the version is mainly the selection of the appropriate elasticity of the resin to the material: PU 1 - elastic as rubber - we use for the most flexible screens and fabrics (Shore hardness: 40A, Setting time: 5 min, Color: amber) PU 5 - flexible, Shore hardness: 85A , Setting time: 45 min, Color: black or natural) - see more PU 9 - flexible, Shore hardness: 45D, Setting time: 15 min, Color: black or natural) PU 021 - version that does not require the highest aging parameters and fatigue. Mainly selected for the production of filters, e.g. in ATK 812 SL cassettes and frames - a liquid version of elastic rubber based on silane bases - flexibility such as PU1 - one-component product ATK GUM - the so-called liquid rubber based on epoxy bases for special applications at elevated temperatures and strong chemicals. Packages of 50 ml and 400 ml. in an easy-to-apply cartridge, for the production of 1, 5 and 20l for manual mixing with a stirrer What we use for: repairing holes, tears and cracks, regeneration of e.g. torn fasteners - hooks of ANKER couplings, clipper connections, production from the base material and ending the edges of the tape, of course earlier cutting with a knife for heat in the form of: filter sieves filter belts filter fabrics non-woven mats filter cartridges and filter cassettes bags for drying, segregation, separation, aeration, filtration, drainage, separation and protection. Made of materials such as: polyvinyl chloride PVC polyamide nylon PA polyester PET polyurethane PU PUR polyolefins PP, TPO, TPE, TPU (with 822 or 823 primer) metal - flexible steel mesh - ending - coating around it can also act as a gasket. User manual - repair and production that we can perform: We have 4 main applications: 1. edge endings 2. insertion of metal fasteners - clasps 3. repair of a torn hole - a hole in the middle with insertion of a mesh 4. production of filters (pouring in a cassette, etc.) Edge ending provides a tear-proof protection. fusion - delamination and distribution of stress evenly over the entire surface of the mesh-fabric and in some cases as a seal when the element is later twisted between the surfaces. After unfolding and straightening the material, pour the edge to the desired width. The thickness can be adjusted by choosing a denser version, e.g. instead of PU5, choosing PU9 or 021 or by making a mold. Remember not to move or remove the hooks until fully set. In the case of plastic nets or mats, it is recommended to cut the materials with a warm knife, which additionally melts the edges. In the case of endings with a pvc overlap, if there is a possibility of welding - then we choose the Bosite-D 2 welding machine. Inserting fasteners - clasps - hooks, e.g. ANKER We have here basically the same flooding as in point 1. Of course, we protect the fasteners from getting in glue 3. Repair of torn meshes with or without material losses - in the case of "only cutting" it is enough to flood the crack with an overlap of 2-4 cm around - in the absence of material, insert the native material and pour 2-4 cm wide. around the patch 4. Production of filters by pouring materials in the base, cassette, etc. ATK PU 021 is most often used, mainly because of the price, as for the highest parameters, it is better to use ATK PU9. ATK PU 5/9/16 SERIES - these are pure polyurethanes of the new generation MDI+ polyolio without ordinary isocyanates (they harden quickly on contact with air and a very small decrease in strength over time), therefore they are used in industry replacing the old generation PU.