KEMISKIT FE21 pipe repair and sealing adhesive

An adhesive for repairing leaking and dry cast iron and steel pipes. The glue effectively fills holes, cracks and holes in cast iron or steel pipes. It behaves like steel / cast iron after hardening. It can be machined. After baking, it becomes more fluid and penetrates into small gaps. The consistency allows us to glue in any position: vertical and even elements near the ceiling. For copper pipes, use MED21, for aluminum pipes, use AL21 For PVC pipes, use ATK PVC glue Application quick repair of leaking cast iron and steel pipes repair of cracks and holes gluing heaters, steel radiator radiators - gutters and other sealing of water, sewage and drain pipes, etc. Technical data: Weight ratio of the apartment: 10A: 1B Volume ratio of the mixture: 3A: 1B Shear strength N / mm2: 22-24 Open time: 30 minutes Curing time at 20 ° C: 24h / 20 ° C 80 min / 80 ° C Continuous temperature resistance: - 40 ° C ≤+ 200 ° C Mixture viscosity (mPas): paste Appearance / color: steel Packaging: 33ml / 100g How to repair a broken cast iron pipe? clean the surfaces with sandpaper for 3-5 cm more than the damage, wash with a degreaser from the set, etch the surfaces AP1 and wait approx. 15 minutes. (it is worth to slightly heat the surface) mix the glue in the right proportion, apply the adhesive well rubbing so as not to leave air between the layers, after 2-3 layers you can flood the mesh it will be easier for you to achieve the required min 2-3 mm. and additionally you will strengthen the whole thing, heat it up with warm air, unless you've done it before. leave to set, Repair kit for cast iron pipes contains: 1. Epoxy KEMISKIT FE21 adhesive 30ml / 100g 2. Degreaser for plastics 100 ml 3. Metal etch AP1 5 ml 4. Mixing kit: Plastic washer, 4 sticks for application, Spatula 5. Flexible metal mesh 12x15 6. Plasticine ATK METALFIX (steel, cast iron) (120g) How to use: 1. Sand the surface with a wire brush for raw metal, removing old paint, oxides collected on the surface and other impurities 3-5 cm around the crack / holes / damage. 2. Prepare a portion of steel plasticine so that, after subsequent pressure, the thickness reaches 1-2 cm - cutting off a piece and kneading to a uniform color (the second ingredient is inside, just cut it crosswise) 3. Press firmly compressed mass to stop the leak and hold until it hardens ( wrap the pressed mass with a bandage, reinforced tape, steel or webbing belt; or apply a stiff pressure) 4.after hardening, sand the surface of the mass with sandpaper and degrease it to remove the dust / grinding residues. 5. Stir Kemispox FE21 in the correct proportion. 6. Apply well on the surface, rubbing 2-3 layers so that the whole thickness is 2-3 (if the meringue is more, the better). Remember / important: 1. Remember to rub kemispox into the surfaces in layers to press the product well, thus removing air from subsequent layers. 2. Use the supplied degreaser for degreasing. Do not use gasoline, denatured alcohol etc. as these are removers and not degreasers. 3. If there is high pressure - it is worth using a metal or reinforced plastic mesh, apply a thicker layer of glue 5-10 mm and on a larger surface min. 5cm. Our advice, in words, in writing and through experience, is the best of our knowledge, but only non-binding guidelines are relevant, also with regard to any third party property rights, and does not exempt you from your own trials of the products we supply with regard to their suitability for certain technology and goals. We ensure, of course, the absolute quality of our products according to the general terms of sale and delivery. KEMISPLUS - Manufacturer of adhesives for industry for over 30 years. He has developed and continues to improve his 3 main brands KemisKOL, (anaerobic adhesives) KemisKIT, and KemisPOX, (epoxy adhesives). All production is carried out in Slovenia.